|You have the option of coming to us for fitting of your Rock and Roll Bed or arranging fitting yourself. If you are also having matching front seat upholstery, you will need to come to us to exchange your existing front seats.
Fixing Kits and Fitting Instructions are supplied with the Rock and Roll Bed to customers who do not come to us for fitting.
Fitting instructions and diagrams are given as guidance only and are based on a SWB vehicle without any modifications. Streamline Auto-Beds Ltd do not accept responsibility for any damage caused from 3rd parties' incorrect measuring or drilling.
We recommend that you insulate, ply line and lay your floor covering before the Rock n Roll Bed is fitted. It can be tricky trying to lay floor covering around a Rock n Roll bed once it has been fitted. If you are starting from scratch, we recommend at least 12mm ply floor and 6mm on the side panels. If your vehicle already has ply floor fitted, we can usually work with it. 9mm is fine. We also recommend that you do not batten your vehicle, especially the floor; battening with ply in between the corrugated floor is ok. Battening with roof lath and creating space between vehicle floor and ply floor is not ok.
We advise all of our customers to have the Rock n Roll Bed fitted first, before purchasing or fitting cupboards. Otherwise you run the risk of either the bed not fitting in or the cupboard doors being in the wrong position and not being able to access them properly. Before you buy or make cupboards for your new conversion, please bear this in mind.
Please Note: If your van already has cupboards fitted, we strongly advise that you take measurements. Please follow these instructions to accurately measure for your Rock n Roll Bed:
Measure 50cm from your rear door rubber towards the front of your vehicle. At this point measure up the passenger side 102cm high. This is the point where you need to take the measurement for the width of the bed from side to side because this is where the top of the frame comes to and it is where your vehicle curves in slightly. This measurement will determine the width of the Rock n Roll Bed that will fit. Allow an extra 2.5cm wiggle room for the width.
If you are unsure that you have enough space, please call us prior to ordering. Streamline Auto-Beds Ltd do not accept responsibility for beds not fitting.
Our Fitting Procedure
All our Rock n Roll Beds are fitted on top of any flooring which has been laid.
Our MOT compliant bed is fitted by drilling 4 holes through the vehicle floor. Spare wheel is dropped and plastics on T5’s are dropped. The bed is fixed with 4 high tensile zinc plated bolts, 5mm spreader plates and locking nuts. Allow 1 hour for fitting
Our M1 tested bed is fitted through the vehicle floor with H Frame that fits over the cross member or L Plates that lip up to the cross member, depending on the vehicle. Spare wheel is dropped and plastics on T5’s are dropped. Allow one and a half hours for fitting.
We strongly advise that all customers read through the information provided for fitting.
Monday to Wednesday - 9.00am to 4.00pm
Thursday - 9.00am to 3.00pm
Friday - 9.00am to 2.30pm
Availability & Bookings
We carry a large amount of Rock and Roll Beds which are available to take away. Please be aware that our upholstery stock changes constantly. Turn-around is usually 1 week if we do not have the upholstery you are looking for in stock.
Fittings must be booked to avoid disappointment. We work on a strict Timed Booking System.
Office Hours to arrange bookings are Monday to Thursday - 9.00am to 6.00pm and Friday 9.00am to 4.00pm
We are offering FREE FITTING on all Rock n Roll Beds until further notice
Terms and conditions for FREE FITTING:
Ply floor must be in place and the vehicle needs to be clear of all obstructions, e.g. cupboards, other seating, speakers, leisure batteries, heaters, luggage, tools, etc. floor runners or risen bolts.
Free Fitting only means that the bed is fitted in standard position at rear of van, (passenger side if 3/4 width bed), free from obstructions.
During our busy periods we cannot fit the bed in any other position or remove obstructions to make the bed fit. It is the customer's responsibility to make sure the vehicle is ready and prepared prior to fitting.
If the bed is to be fitted in a different position other than stated above, this will have to be the customer's responsibility and a fixing kit will be supplied. The bed will be on a supply basis only, unless previously agreed by email prior to booking.
If cupboards are fitted to the vehicle prior to the fitting of the Rock n Roll Bed, it is the customers' own responsibility to check measurements. We do not accept responsibility if the bed does not fit and we will not be able to 'make it fit'.
Streamline Auto-Beds Ltd reserve the right to refuse a fitting in the following circumstances:
Bare metal floor without any lining.
Battened floor; battening with roof lath, creating space between vehicle floor and ply floor.
Obstructions; cupboards, other seating, leisure batteries, speakers, electrics, heaters, floor runners, risen bolts, luggage or tools.
Spare wheel seized on or locking wheel nut key not provided.
We will assess if it possible for fitting to take place, depending on what the issue is and whether we have time available. This will be chargeable at a rate of £40+VAT per hour.
Delays & Cut Off Times
We understand that sometimes our customers are delayed due to unforeseen traffic situations. We work on set timeslots and where possible we will accomodate for this.
Please phone us and inform us of any possible delays.
Even though we are open until 6.00pm Monday to Thursday and 4.00pm on Friday, we need to allow time for fitting.
Cut Off Times for fitting in these circumstances are:
4.00pm Monday to Wednesday
Past this point the bed can still be collected up to half an hour prior to our closing times and will be supplied with a fixing kit and fitting instructions for the customer to arrange own fitting.
We currently only offer delivery to the UK mainland.
We offer delivery on our Rock n Roll Beds which costs on average £70 to mainland UK, depending on Postcode. Please contact us for an accurate delivery cost before ordering
Delivery to Mainland UK
A delivery date will be mutually agreed with you. Your contact number will be passed on to the couriers, who will be instructed to give you a call 1 hour before delivery. Delivery will be made to the registered delivery address.
Delivery can be between 8.30am and 5.30pm. If there is nobody to receive delivery on the above date the pallet will be returned to the local depot. A re-delivery charge will apply unless you wish to collect direct from the depot.
Please be aware that we have no control over the service provided by our couriers. However, if you do experience any problems please call us to make us aware and we will help as much as we can. If for any reason delivery is not made on the above date no compensation is given or implied. Please see our Terms and Conditions.
Please check delivery before signing for it and if the packaging looks damaged in any way please sign for as “damaged”. This helps us if any damage has occurred during the delivery process.
Delivery to UK Offshore Islands, Eire & Europe
We have ceased delivery to offshore islands, Eire & Europe for eBay customers until further notice.